What to Expect During a Siding Installation

This allows for the siding to shift, assuming you don’t nail the nails in too tightly, when weather causes expansion or contraction. Vinyl siding is often the preferred option for siding because it’s low maintenance. While wood needs to be cared for, vinyl siding can be installed and not touched for years. It’s less prone to damage from insects or wind, the color doesn’t seem to fade, and its longevity makes it an economical option. Urban Exteriors specializes in providing top-notch vinyl siding installation tailored to withstand Wisconsin’s unique climate.

Remove and store anything that’s currently near exterior walls, such as patio furniture, planters, and outdoor decorations. You’ll achieve beautiful curb appeal and enjoy knowing your house is protected from the elements. As you make this valuable investment, if you’ve never replaced your siding before, you may be wondering what to expect.

Remove Exterior Fixtures:

You will use your steel snips for this cut since they make the most precise cuts in small areas. Check out the video below for more instructions on installing steel siding around light blocks, faucets, and lights. Experience the benefits of expert home siding installation from Universal Windows Direct. Our UniShield® vinyl siding offers exceptional durability and energy efficiency, providing long-lasting protection for your home. Engineered to withstand the elements, our low-maintenance siding for homes resists fading, cracking, and warping, ensuring a beautiful exterior that lasts.

In Ashwaubenon, where local building codes and weather patterns are specific, hiring experienced contractors who understand these nuances is key.
While vinyl siding is low-maintenance, some care is required to keep it looking its best and functioning properly.
The average cost of a siding installation on a median-sized home in Michigan is between $8,250 and $41,250.
Ensure the soffit panels are securely seated in the J-channels, but allow for some movement to accommodate expansion and contraction.
Now that you know you have the resources to install the siding, think through the design you want for your exterior.

Siding the Walls

Install J-channel around windows, doors, and other openings by nailing it to the wall, leaving a small gap for expansion. Although the installation of soffit and fascia can be challenging, mastering these aspects will result in a refined and professional look for your vinyl siding project. Organizing and keeping a clean workspace is critical for efficiency and safety during the installation process. A level and smooth surface is the most suitable for a vinyl siding installation workspace. Preformed eaves flashing/drip edge should be installed under the starter course of the shingle roofing. If eaves troughs (rain gutters) are used, the flashing edge also helps to direct the water into troughs.

Flashing Installation

This was my most recent build job.It’s all vinyl,including posts and railings.I framed,roofed ,sided ,painted the interior and trimmed it out myself.The rest was left to my subs. Where the big garage roof comes down and hits the side of the big house, did you run a big valley flashing up the wall? I’m trying to imagine 2 feet of snow in that space between the house and the garage. This was my most recent build job.It’s all vinyl,including posts and railings.I framed,roofed ,sided ,painted the interior and trimed it out myself.The rest was left to my subs.

Door and Window Flashing

During my time in the industry, I have learned to appreciate the value of a good installation and the technical features of our products. Our products deliver amazing results for homeowners, but they can only function at their prime when installed correctly. I see common vinyl siding installation mistakes in the field, and I know you might, too. Join us as we share the four common vinyl siding installation topics that Jan often addresses with dealers and installers. Our certified vinyl siding installers ensure your vinyl siding is installed correctly and upholds the highest standard of quality and performance. Vinyl is the most popular siding material in Grand Rapids and protects more than 60% of homes in the U.S.

Installing Soffit Panels

This extra half inch will be cut out so you can intersect the other piece of j-channel together. Mark your measurement on the j-channel, cut it, and install it. Make sure you have the j-channel behind the start and the j-channel is flush with the top of the door or window. You will need to install j-channel for around all your windows and doors before starting your siding, it will make the installation of the steel siding much easier. Check out the video below for the full installation instructions and tips. The top piece of vinyl siding requires extra care during installation.

If you also include painting the siding, this will add a few days to the project.
Siding installation is not just a project; it’s a shield for your home or business.
A successful vinyl siding installation, just like any major project, starts with good planning.
Ensure everything is in good working order because there’s nothing worse than a dull blade in the middle of a cut.
Vinyl is installed by basically clipping it in place along its trim pieces, or channels, that secure the vinyl siding in place while also concealing the nails.
Whether you’re starting from scratch or replacing old siding, the journey boils down to a step-by-step process that’s completely doable, even for beginners.

A Basic Guide to DIY’ing Vinyl Siding

We discuss exposed and concealed fastener systems and go over the top 5 metal siding panels and their costs. In this video we will show you where to place the screws and how to overlap the metal siding panels. Base trim will be installed after the underlayment and prior to the siding panels. So, when you’re cutting each vinyl siding panel, you should account for about 1/4” of extra space at both ends of your siding runs.

Also included in the box and behind the siding is the foam backer that will add rigidity and insulation value to your home. Another piece that helps with the TruLog™ metal siding installation is an outlet block. An outlet block is a base and cap system that helps the siding to be accepted to your faucet, electrical outlets, and lights on your exterior walls. It gives your exterior wall penetrations a nice, finished look. The shake starter strip should be up off the surface of the flashing because we need enough space for the bottom lock underneath the starter strip and up and engaged into the strip. There are several methods that you can use, but all of them begin by terminating the vinyl siding before adding the shake.

Installing the starter strip and corner posts

Carefully nail the upper portion of the fascia with 4D galvanized or pre-painted nails. When joining fascia pieces in the corners, run slightly past the original eave fascia, and butt the intersecting gable fascia against this overrun. If the soffit on your home wraps around a corner, as with a hip roof, you’ll need to make some provisions for the soffit material’s change in direction at the corners. To accommodate this change, nail two J-channels diagonally between the corner of the house and the corner of the roof. Then, cut the first soffit sections to fit this angle and install subsequent sections in both directions.

And with those new shiny siding panels up, your home won’t just have curb appeal; it’ll be a testament to your hard work and skill.
You might wonder how studs could possibly allow so much energy loss in a home.
We are trained to work in ALL weather and understand your concerns; hence, we enhanced our Winter Worry-Free Installation Program.
Begin fastening in the center of the panel and work your way toward the ends, making sure the panels are securely locked along the length of the bottom.
Installing this trim will ensure water runs away from your windows correctly and prevent it from getting under the sill.
Our team is ready to answer all your questions and offer you a free estimate for any of our services.
For expansion and contraction, leave a quarter of an inch around all openings.

Installing the Last Row

Adequate Clearance Roof replacement – There should be a sufficient gap between the siding and adjacent surfaces, such as roofing, windows, and the ground. For example, siding should not be in direct contact with the soil, as this can lead to moisture damage and pest infestations. Make sure the siding has the versatility to meet the varied needs of your specific project. Ply Gem Mastic’s EverPlank luxury vinyl siding is a low-maintenance siding solution that’ll last for decades. Ply Gem is the most-popular vinyl siding manufacturer in North America— and for good reason! They’ve been a leading innovator of siding technology for 75 years and offer a V.I.P. limited lifetime warranty.

They are most commonly used with horizontally applied siding applications such as bevel.
Our certification program helps improve end results to minimize issues and callbacks.
Whether you’re looking to improve your home’s aesthetics or boost its value, proper siding installation is crucial.
Begin by nailing the J-channel to the sidewall flush with the gable.
The terrain and number of stories will impact your final quote and installation time.

Vinyl Siding Resources for Expert Installers

When installing siding, take your time and be careful not to miss any step. Before we delve into the details, please know that professional siding installation services are readily available at Your Window Solutions. Price should be a consideration but not the ultimate deciding factor when choosing a siding material.

Less Maintenance and Longevity of Siding

Use J-channel around the edges, trimming it to size as needed, making those clean cuts you’ve mastered, and securing it with nails; it’s all about the small details. This finishing touch not only provides a polished appearance but also safeguards your siding by directing water away. This is the point where precision cutting with tin snips or a utility knife is your best friend. Undersill trim, which is specifically designed to help guide water away from the house.

Doing these things will make it easier for the team to get right to work transforming your home exterior. When evaluating a home, whether for purchase or renovation, taking the time to inspect the siding’s installation can save you from costly repairs down the road. You can maintain your siding by cleaning it regularly and inspecting it for any signs of damage or wear and tear.

Vinyl Siding Installation Step #7: Siding the Walls

With the starter strips and flashing properly installed, you’re ready to move on to the main event – installing the siding panels.
When the vinyl siding cannot grow during the summer, it results in buckling—which is bad news.
Upgrade your home’s curb appeal with Ply Gem Mastic siding – durable and beautiful solutions for every style.
The durability of vinyl siding means it can withstand the varied Wisconsin weather without warping or fading.
Most siding suppliers can help confirm your materials list based on your measurements.
James Hardie recommends 6-inch-wide flashing that overlaps the course below by 1-inch.
Trespa Pura NFC® Sidings are a versatile solution for most cladding projects because they offer maximum design freedom and a long lasting, beautiful finish.
It’s remarkably easy to install and comes in a huge range of hues, textures, and styles.

Your contractor will make sure that your home is properly insulated by adding new insulation that is appropriate for the siding being installed. Properly cut and fitted siding will ensure a polished and professional appearance. Proper nail placement will ensure a secure and long-lasting siding installation. Properly installed trim will not only enhance the appearance of your home but also provide added protection against water infiltration. By following these steps, you can achieve a clean and polished look for your window and door trim.

Corner post installation and angled cuts for gables will ensure a polished and professional look for your home’s exterior. The finishing touches of your vinyl siding installation include window and door trim as well as sealing and caulking. These final steps will complete the polished appearance of your home and ensure its protection from the elements. The fundamental part of vinyl siding installation is the installation of siding panels. This stage involves cutting techniques, attaching the siding panel, and ensuring proper alignment and overlap. After removing the old siding and trims, repairing any damage and applying a water-resistive barrier to prevent incidental water infiltration is imperative.

Vinyl siding is primarily made of polyvinyl chloride (PVC) but also includes various additives for enhanced durability and UV resistance. How to pick high-quality vinyl siding that will stand the test of time. Check out what makes us the best siding installation crew in Kansas City—and discover the benefits of new siding for your home. Once your old siding is removed, the crew can check for damage such as wood rot—something that’s common with old stucco.

Thank you for requesting an appointment with Coastal Windows & Exteriors.

The flashing should tilt downward to allow water to drain away from the wall. Do not caulk where the flashing and trim or other materials meet. Your starter strip will determine the success of your siding, so take plenty of time to install it well. Your corner posts secure your siding panels around corners, preventing water damage while achieving a neat finish.

However, we suggest siding installation projects only be completed by contractors or highly skilled and experienced DIYers. We also recommend two or more people work on the project together. For this reason, you’ll want to make vertical cuts on the siding panel using a saw or tin snips. If the siding is nailed too tightly, the movement will be restricted, and the siding could potentially buckle and crack. If the siding is nailed too loosely, it will tend to sag when temperatures increase during the summer months. The way nails are installed is critical to how your siding looks and performs.